4
4.0
Mar 22, 2021
03/21
by
Shawn (kresty)
data
eye 4
favorite 0
comment 0
A friend wanted some holders for the micro automotive relays for his car. So I whipped up this model. 5mm diameter hole for mounting. He's planning to use them with the wires in the recessed bits and then fill that with resin after wiring. Since the relays are symmetrical they could be used the other way. I posted this with groups of 1, 3, or 6 relays. There are two different orientations for the mount. The screw holes are 5mm, so a #8 or M4 screw would work with a bit of clearance I printed a...
Topics: relay mount, stl, Relay, Automotive, Relay holder, thingiverse, relay case
10
10.0
Jan 13, 2021
01/21
by
Nathan Smith (malebox)
data
eye 10
favorite 0
comment 0
I originally printed out a remix of thehair's [4-Channel Relay Module Case](https://www.thingiverse.com/thing:2351293). It fit like a glove! When I looked for a single relay version, I couldn't find any that fit the 5V relay I purchased. I'll leave a link to the exact relay I purchased below. It may fit other single relays, but I can't guarantee it. I also threw in a 50mm x 50mm Mount Arm version for those that need it. Figured I'd beat you to the punch, as this seems to be a topic among other...
Topics: arduino_relay, thingiverse, Electronics, stl, Tolako, relay, Single_Relay_Mount, Relay_Case,...
5
5.0
Jan 9, 2021
01/21
by
James Blake (artyficial)
data
eye 5
favorite 0
comment 0
This is a DC 24V 1 Channel Relay Module cover ability to mount on your Ender 3 Printer using the v-rails. (https://www.amazon.com/dp/B00LW2H5GC/ref=sspa_dk_detail_0?psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUFFV0dJSThaSUIwUTkmZW5jcnlwdGVkSWQ9QTA4NzkwNDUySFVGOUxBVDlJRTZaJmVuY3J5cHRlZEFkSWQ9QTAzODg4MDQxMzVJOFBTOTRIREhMJndpZGdldE5hbWU9c3BfZGV0YWlsMiZhY3Rpb249Y2xpY2tSZWRpcmVjdCZkb05vdExvZ0NsaWNrPXRydWU=) This is the relay I used. It stays closed with 4 x M2-20 bolts. It is a clean and simple design....
Topics: relay box, thingiverse, stl, relay, 3D Printer Parts, relay cover, relay_board_mount, Relay_Case,...
9
9.0
Apr 28, 2021
04/21
by
Robert Westgarth (Robba_duck)
data
eye 9
favorite 0
comment 0
For a Kit car project I needed a Relay holder that would hol dup to 6 Relays with the possibility for expansion. Here is the 3rd .1 iteration of the design that has a side 1 and 2 that simply push together should you require more that 6 relays. the tolerance is a little loose but you can glue if required. the design idea is that you have Relays sitting on the outside top and bottom rail with the Wiring in the Centre. The holes for the relays them selves are large enough for actual Relay plugs...
Topics: thingiverse, RELAY_HOLDER, AUTOMOTIVE_RELAY_HOLD, stl, relay_bracket, Automotive, RELAY,...
3
3.0
Mar 26, 2021
03/21
by
Dieter van der Westhuizen (dietervdwes)
data
eye 3
favorite 0
comment 0
This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/li5koDLeSuF
Topics: stl, Relay_Case, relay box, thingiverse, relay_board_mount, double_relay, 3D Printing, relay
3
3.0
Jun 11, 2021
06/21
by
Cid B (Samongo)
data
eye 3
favorite 0
comment 0
Snap together Case for a single relay.
Topics: Relay_Case, Electronics, stl, relay_board, thingiverse, relay_board_mount, relay
5
5.0
Mar 3, 2021
03/21
by
Carl Janetzki (Mykorhiza)
data
eye 5
favorite 0
comment 0
I made a few changes to haopi's original design to better suit my use and relay board that I ordered. I made the holes into a bigger opening so that it would be easier to change wires and access the screws. Changes were made in Tinkercad and printed on a Flashforge Adventurer 3.
Topics: Relay_Case, relay, relay_board, Electronics, thingiverse, relay_board_mount, stl
3
3.0
Jan 7, 2021
01/21
by
QIAN ZHU (xiaoqianzi)
data
eye 3
favorite 0
comment 0
eh what should I say, good luck
Topics: relay_board_mount, stl, 4_Channel_Relay, Relay, thingiverse, Electronics, Relay_Case
4
4.0
Apr 28, 2021
04/21
by
Dioslan Garcia (BountySpace)
data
eye 4
favorite 0
comment 0
The case was designed for these relays. https://www.amazon.com/dp/B07M88JRFY/?coliid=IBZPETNJTK156&colid=39KWBGWEULW72&psc=1&ref_=lv_ov_lig_dp_it The lid is meant to clip on and can be slid of so as to not damage the fragile clips. The holes on the lid are there for access to the connectors as well as aesthetics. Hardware: M3*6 No.4 x 1/2 Round Hd
Topics: thingiverse, Relay, 5v Relay, stl, Electronics, Relay Case
4
4.0
Apr 13, 2021
04/21
by
Giovanni Esposito (Giovanni73)
data
eye 4
favorite 0
comment 0
Scatola copri relè
Topics: thingiverse, relay, stl, relay box, Relay_Case, Electronics
3
3.0
Apr 8, 2021
04/21
by
Bartosz Szafarz (bszafarz)
data
eye 3
favorite 0
comment 0
Simple stand for relay KY-019
Topics: Relay_Case, relay_stand, Electronics, relay, stl, relay_board, KY019, thingiverse, Relay_Standoff,...
6
6.0
Apr 20, 2021
04/21
by
(OneeShaman)
data
eye 6
favorite 0
comment 0
A top part of a case for a 3 channel relay shield. Use the original source file for the bottom part of the case. I needed a case for my raspberry pi IoT device and i didn't find any that would be suitable for my needs and thus i made this. I don't think i will update this further. Feel free to modify it to your needs!
Topics: thingiverse, Relay_Case, stl, relay_board, 3D Printing, Relay_Shield, rpi_relay, 3_channel_relay
10
10.0
Apr 17, 2021
04/21
by
Leonardo Garcia (haopi)
data
eye 10
favorite 0
comment 0
I've modified the length between the holes (front to back) in the original version https://www.thingiverse.com/thing:336948/apps/print/#apps, resulting in a nice snugged fit. Thanks to clough42. Still need to move the screw holes a bit to the edge (on the high side) for perfect alignment, but you can still have access to the screws. Please bare with me. I'm taking this as a challenge to learn Blender.
Topics: relay_board, relay_box, relay, thingiverse, stl, 8_channel_relay, relay 8 channel,...
4
4.0
Jan 8, 2021
01/21
by
mark richard (markr959)
data
eye 4
favorite 0
comment 0
This is a case to hold a 4 channel relay board. You can either print the 'tight' lid which is held on by friction, or the 'magnet' lid. For the magnets: You'll need 2 8mmX3mm hobby magnets. Glue one in the base and one in the lid. Of course, make sure when you glue the magnets, you put the north/south sides facing each other so they attract. These hobby magnets are super cheap and it's so much easier to pull lids off. I've used them in all the cases I've printed. They hold tight, are easy to...
Topics: relay_board_mount, stl, 4_Channel_Relay, Relay, Raspberry_Pi, relay_board, thingiverse,...
3
3.0
Mar 25, 2021
03/21
by
Joshua Page (nickodemous)
data
eye 3
favorite 0
comment 0
Support for a single relay module having screw holes at 20mm and 28mm. Support has screw holes on opposite sites for fixing to a service. This is an implementation of the [component](https://www.thingiverse.com/thing:3853375) by the same name. See component for additional information
Topics: stl, Single_Relay, thingiverse, Electronics, relay_board_mount, Single_Relay_Mount, relay
8
8.0
software
eye 8
favorite 0
comment 0
4
4.0
Mar 25, 2021
03/21
by
Joshua Page (nickodemous)
data
eye 4
favorite 0
comment 0
Single Relay Module Support with holes at 20mm and 28mm. Support has mounting screws on one side and is meant to have the other side braced against a perpendicular surface. Useful when you can only access one side for mounting screws (tight places) This is an implementation of the [component](https://www.thingiverse.com/thing:3853375) with the same name. The the component for more details.
Topics: stl, Single_Relay, thingiverse, Electronics, relay_board_mount, Single_Relay_Mount, relay
16
16
Oct 19, 2020
10/20
by
Center for Accessible Technology in Sign
movies
eye 16
favorite 0
comment 0
ASL vocabulary
Topic: relay
A three piece band straight outta' the blueberry capital of the world. Catchy guitar riffs, exploding drums, led by funky bass lines will keep you coming back for more. Started back in high school relay are: Mark Penza(guitar,vocals) Mark Catalfamo(Bass,Vocals) and Richard DeMarco(drums). These guys are a high energy band with lots of catchy tunes that you'll find yourself humming for weeks to come. One listen and you'll be on the dance floor at all the shows. Download some music and book them...
Topic: Relay
3
3.0
Sep 8, 2021
09/21
by
Orme, David
texts
eye 3
favorite 0
comment 0
26 pages : 20 cm
Topics: Relay racing -- Fiction, Relay racing
311
311
Jun 1, 2010
06/10
by
Gavrilov, M. A
texts
eye 311
favorite 0
comment 0
Terminology of theory of relay devices - relay elements, characteristics, structure, functional properties, analysis, and synthesis
Topics: FUNCTIONAL ANALYSIS, RELAY, TERMINOLOGY, RELAY
19
19
Dec 25, 2020
12/20
by
Center for Accessible Technology in Sign
movies
eye 19
favorite 0
comment 0
ASL vocabulary
Topic: relay
3
3.0
Jun 21, 2021
06/21
by
Vic Ch (Blackarrow0009)
data
eye 3
favorite 0
comment 0
Wanted to insulate a 2 channel relay board from potential exposed wires whilst protecting from high temperatures so I designed this in F360. Has been printed in ABS-like resin on a Phrozen Mighty 4K and should be printable on any resin or FDM/FFF printer with normal resolution and speeds and minimal supports if at all since overhangs could be bridged easily. Only needs 2x M3 screws to secure but electrical tape around the outside works too if you're short on screws.
Topics: 4_Channel_Relay, 2_Channel_Relay, thingiverse, relay, Electronics, stl, relay_2_channel, 2_channel,...
6
6.0
Mar 17, 2021
03/21
by
Cracked Console (Crackedconsole)
data
eye 6
favorite 0
comment 0
A quick remix of the original, adding 2 small tabs for M3 screws. This is for a single relay [5V relay on Amazon](https://amzn.to/2MleVCA) As always, I've included the sketchup files. I basically imported the orginal STLs, and just added the screw tabs and re-exported it to STL. I've added v2 that makes the M3 mounting base thicker and hopefully addresses issues with certain slicer applications, I've used Cura with great success printing this case.
Topics: Relay_Case, stl, thingiverse, Electronics, relay, relay_board_mount
3
3.0
Apr 2, 2021
04/21
by
Loc Phu (Locomoco)
data
eye 3
favorite 0
comment 0
Created a little enclosure for my 3.3v relay. This fits snug and allows plenty of space for the wires.
Topics: thingiverse, Electronics, relay, relay_board_mount, Relay_Case, stl
4
4.0
Mar 19, 2021
03/21
by
John Sutherland (John8)
data
eye 4
favorite 0
comment 0
This is a back mount for a 30 Amp, Hi-Low, 5,12,24 volt Relay Module. The ends where the terminal is soldered will need to be trimmed for the board to fit. Four Pan Head #4 screws x 1/2" will hold the relay and back mount to whatever. Note: This relay can NOT be made latching with a 2.2Kohm resistor like the 10A version. There is a 30A relay board that can be made latching, it has rounded corners and a big (clear) red LED activation indicator. Relays can be found on eBay or Banggood. A...
Topics: Relay Standoff, relay, Relay Mount, Electronics, thingiverse, songle, Relay Holder, 30 Amp, YYG-2,...
10
10.0
Jan 14, 2021
01/21
by
John Banion (jbanion)
data
eye 10
favorite 0
comment 0
Simple relay standoff mount. Module is here: Gikfun 2 Channel 5V Relay Shield Module for Arduino UNO 2560 1280 ARM PIC AVR STM32 Raspberry Pi EK1156 If you like my designs why not tip me a dollar or two. Your support will allow me to spend more time on these designs and their variations. Thanks!
Topics: thingiverse, relay_board, Electronics, stl, relay, relay_board_mount
7
7.0
Mar 3, 2021
03/21
by
movo trab (movotrab)
data
eye 7
favorite 0
comment 0
This is a case for dual channel relays, particular “2 Relay Module”, black board. It is designed to hold the module in place by pressing the top and bottom parts together only. The case consists of 2 parts that are screwed together with four M3 20mm screws and nuts. All holes can be used although to mount the case on a surface or build plate. There is an additional bottom plate with two mounting supports on each side and holes spaced 55mm between.
Topics: 2_Channel_Relay, 2_Channel_Relay_Mount, Relay_Case, relay, DIY, thingiverse, relay_board_mount, stl
3
3.0
Jun 10, 2021
06/21
by
Tony Graf (webdiddy)
data
eye 3
favorite 0
comment 0
Made for the smaller single relays. Print 100% infill, mostly walls anyway.
Topics: Relay_Case, Electronics, thingiverse, adafruit_relay, solid_state_relay, stl
5
5.0
Mar 5, 2021
03/21
by
Jan Ka (BasementEngineering)
data
eye 5
favorite 0
comment 0
This is a relay box for 1 channel relay modules such as [this one](https://s.click.aliexpress.com/e/cfqvVNhe) To assemble it, you will need four 18mm M3 machine bolts. Hook up the AC side of the relay module, clip it into the bottom portion and screw the top piece in place. Now you can hook up some jumper wires from the outside and you are good to go. I uploaded two Versions of the top piece. One with an Inlay and one without. If you want to print two colors with a single extruder printer, like...
Topics: dual_color, stl, relay_box, relay_enc, relay_module, Electronics, Relay, Two_Color, thingiverse
3
3.0
Apr 2, 2021
04/21
by
hendrik golo (hegolo)
data
eye 3
favorite 0
comment 0
I made this Case to fit my 4 way Relay. It is the same height as the raspberry pi case I downloaded from here https://www.thingiverse.com/thing:1572173 That I printed that with the Octoprint cover found http://www.thingiverse.com/thing:3075218 It is not an remix but the idea is the same but the Snap-on works different This is an adjusted version because the one I printed did not fit correctly. hope it is good now. I printed it without supports just with the top\bottom site on the print-plate...
Topics: thingiverse, 4_Channel_Relay, relay, 3D Printer Accessories, relay_board_mount, Relay_Case, stl
10
10.0
Jan 13, 2021
01/21
by
Daniel Salinas (danielsalinas)
data
eye 10
favorite 0
comment 0
This enclosure is for 1 relay board 5v (low trigger), it sells on aliexpress for US$0.60. Link: https://goo.gl/przNA9 To hold the board, you must use hot glue to stick the relay to bottom enclosure, and to close the enclosure permanent you must glue the lid to enclosure. it took almost 40 mins to print. at 0.15mm resolution. NOTE: Just a note, not relevant for the enclosure. This relay does not work good on Raspberry Pi, because it is a low level trigger, I use a workaround to make it work; set...
Topics: arduino_relay, thingiverse, relay_board, Electronics, stl, relay, electronics_enclosure
3
3.0
Mar 13, 2021
03/21
by
(MrQazwe)
data
eye 3
favorite 0
comment 0
A small case for a 1 channel relay module. Useful to attach it to another object and be able to take the relay in and out.
Topics: thingiverse, Relay_Case, relay, case, stl, simple, Electronics, relay_board
3
3.0
Jan 7, 2021
01/21
by
Marc Herter (psyberjunkie)
data
eye 3
favorite 0
comment 0
I could not find a protective case with a possibility to hold the cables in place. This design is simple, you might use some M3x5mm to hold the pcb and the top cover in place. The cables can be secured with zip ties. The fit is tight so have tune your print settings with that in mind.
Topics: protective, relay_board_mount, stl, 2_Channel_Relay_Mount, relay_case, protective_case,...
11
11
Mar 9, 2021
03/21
by
Jeremy Denis (jeremy2nis)
data
eye 11
favorite 0
comment 0
Relay with driver for Arduino on board
Topics: Electronics, relay, relay_board_mount, stl, thingiverse, arduino, relay_board
9
9.0
Jun 20, 2021
06/21
by
ENG Build (EngBuild)
data
eye 9
favorite 0
comment 0
Updates: Mounting holes re-aligned -------------------------------------------------------------- -------------------------------------------------------------- 2 Channel Relay Din mount. Economical design with fast print time Relay I am Using Like share follow and don't forget to post a picture if you make one THANKS! ----------------------------------------------------
Topics: RaspberryPi, 2_Channel_Relay, thingiverse, arduino_relay, DIN, relay, relay_module, arduino,...
3
3.0
Mar 13, 2021
03/21
by
James Balducci (JimbalNy)
data
eye 3
favorite 0
comment 0
Sketched this out to help in designing a 3d printer control box for my Taz 5 SKR 1.4 Turbo upgrade that will allow me to remotely turn the machine on / off with Octoprint by using this relay to control the 24v supply to the board. My heated bed will be on a 100A DC SSR which will be fed straight from the 24v supply (if there's no voltage to the coil the SSR will turn it off anyway so no need to feed that through the relay too possibly overloading it)
Topics: 5v relay, thingiverse, KY-019, 120v relay, KY019, relay, raspberry pi, 10a relay, wingoneer, stl,...
11
11
Jan 11, 2021
01/21
by
Mark-Erik Tölpt (Mark-Erik)
data
eye 11
favorite 0
comment 0
Just a little thing, what I made in school lesson. Little holes on the sides are for zip-ties to lock your relay.
Topics: arduino_relay, thingiverse, stl, relay, relay_board_mount, Relay_Case, arduino, Robotics, frame,...
10
10.0
Apr 30, 2021
04/21
by
Grand Crock (grandcrock)
data
eye 10
favorite 0
comment 0
This is a relay 5V for use in your 3D assembly.
Topics: stl, relay_board, relay, Electronics, thingiverse
4
4.0
Mar 22, 2021
03/21
by
Mike E (someusernamehere)
data
eye 4
favorite 0
comment 0
Relay enclosure for Single Channel Relay Optocoupler Isolation Module Red Board https://www.amazon.com/gp/product/B07BDKCH7Z DZS Elec 5V 1 Channel Relay Optocoupler Isolation Module Red Board 3-5V High and 0-1.5V Low Level Triggered Load AC 0-250V / DC 0-30V 10A SCM IO Control ---- Relay board mounting holes are 45mm x 20mm on center. Uses #4 3/4" machine screws (about 2.75mm diameter) to hold the top on. ---- Used to toggle 120V load line to 5V high-load supply for LED array for Hyperion...
Topics: stl, relay_enclosure, Electronics, thingiverse, relay
8
8.0
Jan 15, 2021
01/21
by
Pakorn Rattanaying (9Arduino)
data
eye 8
favorite 0
comment 0
Case Module Relay 1 Chanel Case Case Module Relay 1 Chanel For Relay is not hold. Produce : https://www.9arduino.com/p/194
Topics: thingiverse, stl, 3D Printer Accessories, Case_Relay, relay_Case, Relay
3
3.0
Jan 5, 2021
01/21
by
Charlie J. Gallo (charliejgallo)
data
eye 3
favorite 0
comment 0
Small case for a 433Mhz relay board
Topics: 433, relay 433mhz, stl, 433mhz, thingiverse, relay, Electronics, Relay_Case
8
8.0
Jun 20, 2021
06/21
by
juan munoz (jmunozar)
data
eye 8
favorite 0
comment 0
Simple minimalistic relay socket, modified from https://www.thingiverse.com/thing:1977671
Topics: relay_socket, thingiverse, relay, Electronics, stl
3
3.0
Apr 24, 2021
04/21
by
Brian Timm (timmehtimm)
data
eye 3
favorite 0
comment 0
I designed this little mount for the 2 Channel relay I'm using to drive my LED lights on my printing setup. I wanted to convert to automatic control using Octoprint's Enclosure plugin. So I made this little mount to hold the relay board and secure it to a wall, lack table, etc. As I have mine on the lack table under my printer I made a little hood that extends to protect the relay from debris and me dropping tools on it. Inlcuded the .f3d file if you want to edit/remix.
Topics: 2_Channel_Relay, relay, stl, thingiverse, relay_board_mount, Electronics, 2_Channel_Relay_Mount
4
4.0
Mar 25, 2021
03/21
by
Joshua Page (nickodemous)
data
eye 4
favorite 0
comment 0
Support for a dual relay module. Mounting screws on one side with other side braced against a perpendicular surface. Useful for situations where only one side is easily accessible. This is an implementation of the [component]https://www.thingiverse.com/thing:3834210) by the same name. See component for more details
Topics: stl, thingiverse, 2_Channel_Relay_Mount, Electronics, dual_relay, Relay_Mount
3
3.0
Jun 19, 2021
06/21
by
Christoph Schwarzenberg (ChrisSzb)
data
eye 3
favorite 0
comment 0
Hi folks, I have created a cover for the 4-Relay Module from Elegoo for a hobby project. Maybe someone else can use it. If you set the upper and lower thickness at housing to 0, the infill pattern comes out. Then it will look the same for you. This may allow a good cooling and it looks great. Have fun printing.
Topics: Arduino_case, Elegoo_Relay_Module, Relay, thingiverse, 4-fach, Elegoo, Kasten, Kiste, Electronics,...
12
12
Jan 14, 2021
01/21
by
brandon kelley (Wupinstick)
data
eye 12
favorite 0
comment 0
I wanted a 2 Channel Relay mount for my AM8 so I modified zer0flag's case. This mount is for the following relay board. https://www.amazon.com/SainSmart-101-70-100-2-Channel-Relay-Module/dp/B0057OC6D8 Use M3 screws to mount the relay to the bottom of the case. I used the same M5 screws listed in the AM8 material list to mount this to the aluminum frame. Use M2.5 screws for the lid. I also printed these M5 nuts so I wouldn't need to take the frame apart. https://www.thingiverse.com/thing:1686927...
Topics: AM8_upgrade, thingiverse, 2_Channel_Relay, 3D Printing, stl, 2_Channel_Relay_Mount, relay,...
10
10.0
Mar 21, 2021
03/21
by
ScottieD369 (ScottieD369)
data
eye 10
favorite 0
comment 0
!!!***(Ver8 is Snap Fit Ver7 slightly loose but can work)***!!! This is for a Relay Module with dimensions: L 43.78mm x W 26.28mm Stand-Off's are hole ready! (No drilling Necessary!!!) Snug Fit and flush mount I also made this so that it can fit ~ 6mm Length screws. (board mount) Lightweight & Strong Base Support! This is my First Project since my Printer has been "Dialed In"!!! (Detailed Prints without hairs and flat,aligned,clean) As long as the bed is level EVERY TIME! I used...
Topics: stl, 1 Channel Relay, Single Relay Mount, Single Relay, 1 Channel Relay Mount, Electronics,...
4
4.0
Jan 16, 2021
01/21
by
Luke Is OK (ltlklr)
data
eye 4
favorite 0
comment 0
Hi, this is just a single channel relay case. The holes are 3.5mm in diameter. The lid is snap fit and it has "RELAY" written on it. For the letters I switched fillament to black.
Topics: Electronics, relay_board, thingiverse, relay_board_mount, cnc, Relay_Case, stl
5
5.0
Mar 4, 2021
03/21
by
Adi Dim (atsnailpace)
data
eye 5
favorite 0
comment 0
A single relay case on power line. How to turn your 3D printer on/off using Octoprint - https://www.youtube.com/watch?v=dQNBeAZpRmk
Topics: stl, 3D Printer Accessories, Relay_Case, thingiverse, relay_board_mount, relay
